乐播传媒视频

Skip to main content

Quad® Brand Ground Rubber Balls

Rubber balls from Minnesota Rubber and Plastics are carefully molded and precision ground for superior performance in the most critical applications.

Material

Our standard rubber balls are molded from a 70 Shore A nitrile compound specially formulated for grinding. Our compound 525K is recommended for most typical
pneumatic, hydraulic or water applications.

Other elastomeric compounds are also available for more demanding situations such as steam, high temperatures or corrosive fluids. Compounds with a hardness lower than 70 Shore A are difficult to grind. Harder materials are also available.

Sphericity

High speed centerless grinding combined with automatic gauging/measuring equipment assures you of a consistent, close tolerance on both spherical and diametric dimensions. The resulting uniform finish also ensures consistent sealing performance regardless of how the ball seats.

Variety of Sizes

Select from our standard sizes below, or take advantage of our custom molding facilities for your specialized ball applications.

Part No.CompoundNominalDiameter (in)Diameter (mm)
B130093525K3/320.093 卤0.003 dia., 0.003sph. Total2.36 卤0.08 dia., 0.08sph. Total
B130125525K1/80.125 卤0.003 dia., 0.003sph. Total3.18 卤0.08 dia., 0.08sph. Total
B130156525K5/320.156 卤0.003 dia., 0.003sph. Total3.96 卤0.08 dia., 0.08sph. Total
B130187525K3/160.187 卤0.003 dia., 0.003sph. Total4.75 卤0.08 dia., 0.08sph. Total
B130218525K7/320.218 卤0.003 dia., 0.003sph. Total5.54 卤0.08 dia., 0.08sph. Total
B130250525K1/40.250 卤0.003 dia., 0.003sph. Total6.35 卤0.08 dia., 0.08sph. Total
B130312525K5/160.312 卤0.003 dia., 0.003sph. Total7.93 卤0.08 dia., 0.08sph. Total
B130375525K3/80.375 卤0.003 dia., 0.003sph. Total9.53 卤0.08 dia., 0.08sph. Total
B130437525K7/160.437 卤0.004 dia., 0.005sph. Total11.10 卤0.10 dia., 0.13sph. Total
B130500525K1/20.500 卤0.004 dia., 0.005sph. Total12.70 卤0.10 dia., 0.13sph. Total
B130562525K9/160.562 卤0.004 dia., 0.005sph. Total14.28 卤0.10 dia., 0.13sph. Total
B130625525K5/80.625 卤0.004 dia., 0.005sph. Total15.88 卤0.10 dia., 0.13sph. Total
B130750525K3/40.750 卤0.004 dia., 0.005sph. Total19.05 卤0.10 dia., 0.13sph. Total
B131000525K11.000 卤0.004 dia., 0.005sph. Total25.40 卤0.10 dia., 0.13sph. Total

Ground Ball Tip Sheet

  • Solid, non-reinforced core ground balls are generally used as check devices for pressures less than 120 psi.
  • When designing an application to incorporate a check ball, the differential area between the projected ball area and the area of the ball channel should be slightly greater than that of the main flow area. This will minimize flow disruption due to the presence of the ball in the flow stream.
  • The ball seat should have an included angle of 120掳 and have a 0.010″-0.015″ radius where the seat and the flow channel meet. For liquids, the ball seat should have a surface finish of 20碌in RMS or better. For air or vacuum applications, the ball seat should have a surface finish of 10碌in RMS or better.
  • At pressures greater than 120 psi, there is a tendency for ground balls to become stuck in the ball seat (checking orifice). If this occurs often, it can damage the ball, eventually causing the ball to extrude through the orifice.
  • As a “rule-of-thumb,” the diameter of a check ball should be at least three times the diameter of the flow orifice. The larger the ball-to-orifice ratio, the lower the likelihood of ball extrusion.
  • Standard tolerances for ground balls are indicated in the following table:
Ball DiameterDiameter ToleranceSphericity
< 0.375卤0.0030.003 Total
> 0.375卤0.0040.005 Total

Need help solving a tough engineering problem?